TV unit design for living room and bedroom

A TV unit is a wall, a console and a tangle of wires. Get the wires and the height right first and the design follows. This guide covers both, then the back panel, the storage and the light.

Send an enquiry Call +91 99500 38059

A guide by Terra & Tones, updated

Media wall, Smoke & Copper. A copper-lined frame set into black marble, with smoked oak above and lit shelves to one side.
Media wall, Smoke & Copper

Start with the screen

Set the centre of the screen at eye level when you sit, which puts it roughly 40 to 44 inches off the floor for a sofa. A screen mounted higher looks impressive in a showroom and strains the neck at home. Keep it off the wall that faces a window, or the afternoon glare washes out the picture.

Hide the wiring first

Run conduits inside the wall for power, HDMI, the set-top box, the soundbar and the router, with a recessed box behind the screen so the plugs sit flush. Leave one spare conduit, because devices change faster than walls. Give the set-top box and the games console a ventilated shelf: electronics shut inside a closed drawer overheat.

The parts of a TV unit

  • Back panel. The surface behind the screen: stone, large tiles, fluted panels, veneer, laminate or textured paint.
  • Console. A low cabinet, floating off the floor or standing on it, with drawers for remotes and cables. Twelve to eighteen inches of depth is enough.
  • Side storage. Closed cabinets for what you want out of sight and a few lit open shelves for what you want seen. Closed doors keep the dust out.
  • Light. A soft line behind or below the unit. Keep it dim and warm, because a bright strip behind the screen tires the eyes.

Choosing the back panel

Stone gives the richest wall and the heaviest one, so the wall and the fixings must carry the weight. Fluted panels and veneer are lighter and warmer. Limewash or textured paint costs least and suits a calm room.

Whatever you choose, let the panel run past the screen on both sides, so the television sits on the wall instead of filling it.

TV walls in our projects

In Smoke & Copper the screen sits in a copper-lined frame set into black marble, with smoked oak above and lit shelves to one side. The family room in Gulmohar House takes the quieter route: a limewashed wall over a cove-lit floating console, with fluted walnut beside it.

Family room, Gulmohar House. A limewashed media wall over a cove-lit floating console, fluted walnut and shelves hung from the ceiling.
Family room, Gulmohar House

A TV unit for the bedroom

A bedroom unit can be shallower and simpler: a wall-mounted screen opposite the bed, a floating console below, and the dresser or the study table built into the same run. One bedroom in Gulmohar House does this, with a floating console under the screen beside the wardrobe.

Bedroom, media wall, Gulmohar House. A floating console under the screen, a full-height oak door, and a wardrobe with a lit glass bay.
Bedroom, media wall, Gulmohar House

Questions

What is the right height for a wall-mounted TV?

The centre of the screen should sit at your eye level when seated: about 40 to 44 inches from the floor in a living room. In a bedroom, where you watch from the bed, mount it a little higher and tilt it down.

Which material is best for a TV unit?

Plywood or HDHMR for the console and the cabinets, with laminate, veneer or lacquer on the face. For the back panel, choose by weight and budget: stone, fluted panel, veneer or paint.

Should a TV unit be wall-mounted or floor-standing?

A floating console leaves the floor clear, which makes the room look larger and lets the mop pass under it. A floor-standing unit carries more weight and suits a wall you cannot fix into, such as a thin partition.

What we design and build

More guides

Tell us about the room

A kitchen, a bedroom, a whole floor. Send a few lines about the space and we will write back.

Enquire